Can I Install A Tub Myself?
Can I Install A Tub Myself?
Blog Article
Are you on the lookout for critical information concerning A Step-by-Step Guide to Installing a Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a bathtub isn't exactly brain surgery, however it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately difficult job. If the old tub is readily accessible, the job can move quickly; if you have to open a wall to eliminate the old tub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the work and fit trying it. Instead of working with a contractor to take control of a halfway-completed task, it is better to think about using one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will assist you set up a brand-new bathtub in your restroom if you have currently gotten a brand-new bathtub as well as do not require to transform the setup of your previous water pipelines.
Your devices and also material checklist should comprise the following:
Getting ready for the Installment
To start with, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. When the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, position the bath tub in the required setting. The wooden boards are handy in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bath tub up until the level reviews level.
To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Activate the water system and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill the bathtub as well as additionally examine the overflow outlet and the normal electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bath tub should wait till the tub has actually been utilized at least when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The former kind should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, leading to problems with dampness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in use. The sealer can crack fairly early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our part on Installing A Bathtub. Many thanks for taking the time to browse our article. Do you know somebody else who is truly interested in the niche? Feel free to promote it. Thanks so much for going through it.
Recurring Service Plans
Report this page